How do I wake up my Synology NAS?
Go to Joinable Devices for Wake on LAN, enter the MAC address of the target, and click Wake up. To wake up a joined Synology devices (e.g. a Synology DiskStation/RackStation) over QuickConnect, tick Enable WOL over QuickConnect, and wake up the device by login with your QuickConnect credentials.
How do you wake up windows using WOL on Synology NAS?
How To Enable Synology DSM 6.0+ to send WOL/Magic Packet
- Under the Task Settings tab, in User-defined script, instead of having previous ether-wake command replace them with synonet –wake [your mac address here] eth0;
- Once that’s done, you can go back to the Task Schedule page view previous results, Action > View Result.
Can Synology NAS be turned on remotely?
2021/07/27 – Wake on LAN (WOL) allows you to remotely wake up wired devices connected to a Synology router via Synology Router Manager or a QuickConnect ID.
How do you use Wake on LAN magic packet?
Open the Device Manager and expand the “Network Adapters” section. Right click on your network card and go to Properties, then click on the Advanced tab. Scroll down in the list to find “Wake on Magic Packet” and change the Value to “Enabled.” You can leave the other “Wake on” settings alone.
Does Synology have Wake on LAN?
Wake on LAN (WOL) is supported on most Synology NAS models, except for the models listed below. Embedded 10 GbE ports on certain models do not support WOL. To check if your model’s LAN ports support WOL, you can refer to your device’s Datasheet, which can be found in the Download Center under the Documents tab.
What port does Wake on LAN use?
port 3163
The default port that RES ONE Automation uses for Wake-on-LAN is port 3163, but you can select an alternative UDP port number if necessary.
Does Wake-on-LAN work over Wi-Fi?
For most computers, Wake-on-LAN works over Wi-Fi only if the wireless device is the one sending the WoL request. In other words, it works if the laptop, tablet, phone, or other device is waking up a computer, but not the other way around.
Why is Wake-on-LAN so unreliable?
As far as WOL only working a few times, that’s because the router is working off its ARP table/cache. But that’s flushed after about 10 mins once the device is turned off. And then WOL becomes inaccessible for that device. So it’s inherently unreliable.
How does wake on LAN work on Synology router?
Please try again later. Wake on LAN (WOL) allows you to remotely wake up wired devices connected to a Synology router via Synology Router Manager or a QuickConnect ID. This video will guide you through how to configure WOL in SRM and Disk Station Manager, as well as how to wake up devices once you are setup.
Is there a way to send WoL from Synology?
Ever since Synology released DSM 6.0, even in 6.0 beta, the previous method for sending WOL packets no longer works. They have removed ether-wake command (see sample error below), but fortunately, there are still ways to send WOL or magic packet to wake up local network machines.
How to send a magic packet to restart a Synology NAS?
We then look at how you send a Magic Packet to restart a powered down Synology NAS. Wake On LAN – Magic Packet is created by Depicus, and is free to use on Windows, iOS and Android. However, Depicus does charge a small fee for the macOS version. You can download the Wake On LAN software directly from https://www.depicus.com/wake-on-lan/
How to enable and use wake up on LAN ( WOL )?
In this video we show you how to enable the Wakeup On LAN (WOL) function on your Synology NAS. We then look at how you send a Magic Packet to restart a powered down Synology NAS. Wake On LAN – Magic Packet is created by Depicus, and is free to use on Windows, iOS and Android. However, Depicus does charge a small fee for the macOS version.
