Where is the OBD port on a 1995 Jeep Cherokee?

You will find below several pictures which will help you find your OBD connector in your car.

The automotive diagnostic plug is located above the pedals.
The OBD II port is visible above the brake pedal.
Here is the OBD socket.

How do I find my Jeep Grand Cherokee engine code?

Jeep Grand Cherokees Before 1996

Get behind the Grand Cherokee’s wheel and slide your key into the ignition. Turn the key in the following pattern: On-Off-On-Off-On.
Grab a pen and paper and count the number times the check engine light flashes at you. It will be a code.

What causes a misfire on a Jeep Grand Cherokee?

Common reasons for this to happen: Faulty spark plugs or wires. Faulty ignition coil. Broken piston rings. Burnt or bent valves.

How do I find the code for my Jeep Cherokee?

How To Retrieve Your Jeep’s Diagnostic Code

Insert the key into the ignition.
Turn the ignition On-Off-On-Off-On within 5 seconds.
Record the 2-digit DTC as displayed by the flashing MIL.

Why is my check engine light on in my Jeep Cherokee?

If the check engine light in your Jeep Cherokee starts flashing, that means that the problem needs sudden attention and your Jeep should be brought in today. This blinking light mostly indicates a scrupulous engine misfire allowing unused fuel to be deposited into the exhaust system.

What is a 1994 Jeep Grand Cherokee worth?

1994 Jeep Grand Cherokee Value – $199-$1,148 | Edmunds.

Is 1995 Jeep Cherokee OBD2?

ALL ’96 model year vehicles, of whatever make, sold in the US were required to be OBD-II. A number of ’95 year model vehicles (not XJs) were OBD-II and even some ’94 year model vehicles were OBD-II.

How do you clear the error code on a Jeep Grand Cherokee?

How to Reset the Fault Code on a Jeep Cherokee

Pull the release lever to open the hood from inside the vehicle.
Open the hood and place the support rod into position to prop up the hood.
Remove the nut connecting the negative battery terminal to the battery, using an open end wrench.
Allow the computer to reset.

How do I reset the check engine light on my Jeep Grand Cherokee?

To turn off the Jeep Grand Cherokee check engine light, turn the ignition switch to ON but don’t start the vehicle. Press the gas pedal 3 times within 10 seconds and turn the ignition off. Wait 10 seconds and start the engine.

What is causing my Jeep to misfire?

Worn and old spark plug wires are common causes of random misfires. Replace spark plugs and wires if needed and recheck for misfires. If you have determined that your ignition system is operating correctly, there may be a problem within your fuel system that is causing the random misfires. Check fuel pressure.

Why does a jeep misfire?

The cause of a misfire is often from a loss of spark (ignition system), improper air-fuel mixture/lack of fuel (fuel system), or a loss of compression (mechanical). On paper, a misfire may seem easy to diagnose, but there are number of components that need to be inspected before throwing parts at the vehicle.

How to retrieve trouble codes on a 1995 Jeep Cherokee?

Turn your vehicle to the “on” position without firing it up. Switch it back and forth (on, off, on, off and on) within five seconds. This triggers the PCM to go into diagnostic mode. Leave the car on to read the trouble codes. Record the number of times the check engine light flashes.

What does the code 55 mean on a Jeep Cherokee?

Continue recording the engine codes (there may be several) until the check engine light flashes the code 55, which stands for “End of Code Output.” Reference the codes in your Jeep manual or on the Internet to determine any engine problems indicated during the process you’ve just completed. See “Resources” for a link to Jeep code meanings.

Can you check the engine code on a Jeep Wrangler?

When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move. This generation of Wranglers and Cherokees had the most simple diagnostics of any other. You need no special scanner to get the trouble code.

What is the engine code for a Jeep YJ?

Jeep check engine codes for the YJ, XJ and other OBD1 jeeps. Jeep check engine codes for the Jeep Wrangler YJ and the XJ Cherokee. These codes and video may work with other OBD1 Jeeps. When Chrysler / Jeep came up with this idea for getting the engine codes, it was a very smart move.