What does chlorinator off no cell power mean?
‘No Cell Power’ means the current chlorinator cycle has been interrupted due to no voltage being detected when the cell power relay was turned on. Page 4. Turn off power to the controller. Disconnect the.
How do you unlock the configuration menu in aqualogic?
Press the ‘Menu’ until, ‘Configuration Menu-Locked’ appears. To unlock, press and hold the (<) & (>) until the text, on the display, changes from ‘Locked’ to ‘Unlocked’ (unit will beep).
How do I reset my Hayward Aqua Rite?
To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.
How do you recalibrate a Hayward Aqua plus salt cell?
Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.
How do I know if my salt cell is bad?
If the salt cell bubbles, but only a little bit, then you probably have a bad cell. It is still a good idea to call a pool professional to confirm this diagnosis. If the salt cell bubbles vigorously, then it is working fine.
Why does my salt chlorinator says no flow?
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) this will free up the water flow, allowing the system to fully ‘prime’ and function at full capacity.
How do I reset my aqualogic check light?
You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.
Why is my salt cell light blinking?
If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires.
How long should a salt cell last?
about five to seven years
How long should a salt cell last? The answer really depends on the use conditions and how often you do maintenance on your pool. The safe answer is that they usually last for about five to seven years. Salt Cells cost between $200 and $900 to replace, depending on your chlorinator model.
What causes a salt cell to fail?
Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. Doing this ensures excess calcium doesn’t become caked on the metallic plates. Another common cause of salt cell failure is improper water balance.
How do I test my salt cell?
Submerge the salt cell in a bucket of pool water, but do not get the wiring connections wet. Turn on the pump and activate the salt system. Put the output on the salt system at 100% for this test. Put the output back to the original setting when you are done.
When did no cell power start on Hayward AquaLogic?
In March of 2009 my Hayward Aqualogic pool system started displaying the message “No Cell Power” and the salt system in my pool was no longer working. This website details the steps involved in correcting this error.
When did the no cell power message Come On my Aqua logic P4?
This controller serves to control the electrical systems of the pool- generating chlorine and the filter. The controller was warranted for 3 years so it expired in March 2009- (less than 3 months ago). On Saturday June 20th I discovered a “No Cell Power” message on my Aqua Logic P4.
When did I replace the cell on my AquaLogic pool?
My AquaLogic control panel looks a little different than the one in your pictures but the PCB looks similar – including the bad connection on K1. Mine was installed with the pool back in November 2003. I’ve had to replace the cell back in May of 2006 (just inside the warranty).
What does it mean when there is no cell power?
‘No Cell Power’ means the current chlorinator cycle has been interrupted due to no voltage being detected when the cell power relay was turned on. Page 3 Check System Light On:
